Hyundai Getz>> Electric equipment>> Illumination and the light alarm system
Fig. 7.39. Devices and controls system of illumination and the light alarm system of the car: 1 – the block of safety locks and the relay in car salon; 2 – the switch of a signal of braking; 3 – a regulator of brightness of illumination of a combination of devices; 4 – the switch of the proof-reader of headlights;
5 – the switch of external illumination; 6 – the alarm system switch; 7 – the switch of antifog headlights; 8 – the switch of a back antifog lantern; 9 – lamps of headlights of head light; 10 – an antifog headlight; 11 – a lamp of dimensional light; 12 – a lamp of the index of turn;
13 – an additional signal of braking; 14 – lamps of illumination of licence plate; 15 – a lamp of dimensional light and a braking signal; 16 – a lamp of light of a backing; 17 – a lamp of the index of turn; 18 – a back antifog lantern


The illumination system includes the basic headlights (a headlight of head light), back lanterns, braking signals, backing lanterns, turn indexes, antifog headlights and back antifog lanterns, lanterns of illumination of licence plate, plafonds of illumination of a motor compartment and salon illumination. Before replacement of lamps it is necessary to check up a corresponding safety lock and to disconnect the corresponding consumer. Devices and controls are shown by system of illumination and the light alarm system of the car on fig. 7.39.

Colour of a deposit
The possible reason
Deposit of dark colour
Reenriched топливовоздушная a mix
The insufficient maintenance of air in a mix
Deposit of light colour
Reimpoverished топливовоздушная a mix
Too early ignition
Easing of an inhaling of spark plugs

Adjustment of light of headlights
Adjustment of headlights of head light

Fig. 7.42. The scheme of adjustment of headlights: Н1 – height of the centre of a lamp of a headlight of head light over an earth surface; Н2 – height of the centre of a lamp of an antifog headlight over an earth surface; W1 – distance centre to centre lamps of headlights of head light; W2 – distance centre to centre lamps of antifog headlights; L – distance between a lamp of a headlight of head light and the screen


The adjustment scheme is shown on fig. 7.42.
Adjustment of a direction of light bunches of headlights spend by means of the device according to the instruction of its manufacturer.

       THE NOTE
Adjustment of light of headlights spend according to the acts operating in region where the car is maintained.

Fig. 7.40. Adjustment of headlights of head light: 1 – adjustment of a beam of light in a horizontal direction; 2 – adjustment of a beam of light in a vertical direction


Light of headlights is regulated by rotation of adjusting screws (fig. 7.40). In the absence of the special equipment adjustment can be spent as follows.
Establish demanded pressure in tyres of wheels. In the car there should be no cargo, except the driver, a spare wheel and the onboard tool. The storage battery and headlights should be in good repair.
Establish the car on an equal horizontal platform.
On the screen for adjustment spend two vertical and one horizontal lines. Points of intersection of lines define position of the centres of light bunches of headlights.
Adjusting screws move the brightest sites of light bunches to points of intersection of lines on the screen.
Adjustment spend at the included passing light of headlights.

Adjustment of antifog headlights
Adjustment of antifog headlights make, as it is specified for headlights of head light, at a working order of antifog headlights and the storage battery.

Fig. 7.41. An antifog headlight (rear view): 1 – the adjusting screw


Adjust a direction of light bunches of antifog headlights the adjusting screw (fig. 7.41).
The adjustment scheme is shown on fig. 7.42.
Include a passing light of headlights (the car without the driver).

Fig. 7.43. The scheme of adjustment of headlights of head light


Adjust position of light bunches of headlights so that the top borders of light stains have settled down within the shaded zone of the screen (fig. 7.43).
Include antifog headlights (the car without the driver).

Fig. 7.44. The scheme of adjustment of antifog headlights


Adjust position of light stains so that their top border was in a place shown on fig. 7.44 (the shaded sites).

Replacement of lamps

Fig. 7.45. Lamps of a headlight of head light:
1 – a lamp of the index of turn; 2 – a passing light/headlight lamp – a lamp of dimensional light


Lamps of a headlight of head light are shown on fig. 7.45.
For replacement of a lamp of a passing light/headlight a cover from a back part of a headlight. Disconnect wires from a lamp, deduce from grooves short moustaches of a spring clamp and take out a lamp.

       PREVENTIONS
Do not concern lamp flasks barehanded. Fat from the fingers, remained on a lamp flask, evaporates and can settle on a reflector (reflector) that will lead to its dimness. The stains which have arisen on imprudence from a touch to a flask wipe a pure rag without pile or remove spirit.
Necessarily replace fused lamps with lamps of the same type.

For replacement of a lamp of dimensional light take out from an optical element a cartridge in gathering with a lamp and take out a lamp from a cartridge.
To replace a lamp of the index of turn remove a contact socket from a cartridge, turn a cartridge in gathering counter-clockwise and take out it from a nest.

Removal and installation of headlights
Removal and installation of a headlight of head light
Disconnect a wire from the negative plug («–») the storage battery.
Turn away two bolts of fastening of the top facing of a forward bumper.
Turn away bolts of fastening of a block headlight and separate contact sockets.
Installation is spent in an order, the return to removal.

Removal and installation of antifog headlights
Disconnect a wire from the negative plug («–») the storage battery.
Remove forward подкрылок.

Fig. 7.46. A contact socket of an antifog headlight


Remove an antifog headlight, having turned away fastening screws, and separate a contact socket (fig. 7.46).
Headlight installation is spent in an order, the return to removal.

Back lanterns
Removal and installation of a lamp of the index of turn
Disconnect a wire from the negative plug of the storage battery.

Fig. 7.47. Screws of fastening of a back lantern


Turn away two screws of fastening of a back lantern (fig. 7.47).
Separate a contact socket of a back lantern.
Installation is spent in an order, the return to removal.
Removal and installation of the lanterns established at doors of a back, lamp of a parking light and lanterns of illumination of licence plate
Disconnect a wire from the negative plug («–») the storage battery.

Fig. 7.48. Screws of fastening of an upholstery of a door of a back


Remove an upholstery of a door of a back (fig. 7.48).
Take out a lamp of illumination of licence plate and separate a contact socket.
Installation is spent in an order, the return to removal.
Removal and installation of an additional signal of braking
Disconnect a wire from the negative plug («–») the storage battery.
Remove a back spoiler, having turned away four nuts of fastening (on cars with a back spoiler).

Fig. 7.49. Screws of fastening of an additional signal of braking


Turn away four screws of fastening (fig. 7.49), separate a contact socket and remove an additional signal of braking.
Installation is made in an order, the return to removal.

Removal and installation of a plafond of illumination of salon  
Disconnect a wire from the negative plug («–») the storage battery.

Fig. 7.50. Removal of a plafond of illumination of salon: 1 – the roof console; 2 – рассеиватель; 3 – a screw-driver


Having hooked a screw-driver, remove рассеиватель from the roof console (fig. 7.50).
Turn away screws of fastening and separate a contact socket.
Installation is spent in an order, the return to removal.

The block подрулевых switches
Security measures at block removal подрулевых switches from the cars equipped with pillows of safety
At block removal подрулевых switches on the cars equipped with pillows of safety, strictly observe following instructions.
Dismantling or repair of the module of a pillow of safety and contact disk are forbidden. At malfunction replace them.
Do not suppose falling of the module of a pillow of safety and a contact disk, and also hit on them of water, greasings and oils. In the presence of dents, cracks and deformation replace the damaged details.
The module of a pillow of safety stack on a flat surface facing upwards. Do not place on it any subjects.
Do not suppose influence on the module of a pillow of safety of temperature above 93 oС.
After operation of a pillow of safety replace a contact disk new.
At work with the worked pillow of safety use protective gloves and points.
Recycling of not worked module of a pillow of safety spend in strict conformity with instructions on systems of passive safety.
At separation of a socket of the module of a pillow of safety and a contact disk do not apply excessive efforts.
The removed module of a pillow of safety store in a dry and pure place.
At installation of a contact disk combine an adjusting label with an index of neutral position of a disk, establish a steering wheel in position of rectilinear movement and attach a contact disk to the switch of a steering column. If an adjusting label of a contact disk not to combine properly with an index of its neutral position the steering wheel at turn passage will not turn on a full corner or the flat wire in a contact disk that can lead to wrong operation of a pillow of safety and serious травмированию the driver can break.
Removal and installation
Disconnect a wire from the negative plug («–») the storage battery.
Remove the module of a pillow of safety, having turned away three bolts of fastening and having separated a socket of the switch of a sound signal.

       THE PREVENTION
Fig. 7.51. Points of fastening of facing of the switch of a sound signal

On cars without a safety pillow remove only facing of the switch of a sound signal (fig. 7.51).

Turn away a nut of fastening of a steering wheel.
Remove a steering wheel by means of a stripper.

       THE PREVENTION
At removal of a steering wheel do not strike on it — so it is possible to damage the mechanism of folding of a steering shaft.

Remove a facing casing of a steering column, having turned away three screws of fastening.

Fig. 7.52. Removal of a contact disk from a steering shaft


Remove a contact disk (fig. 7.52).

Fig. 7.53. Latches of fastening of the block подрулевых switches


Separate contact sockets and remove the block подрулевых switches, having wrung out downwards latches (fig. 7.53).
Installation is spent in an order, the return to removal.